Dental autoclave
OSA-322D-18L with built-in printer
1 ． General Introduction
This Autoclave is a precision instrument specializing in the operation occasion in
need of simple, fast and efficient sterilization by the doctor or his/her assistants,
and the doctor shall take the responsibility for such work.
This Autoclave is specially designed for the occasions in use of frequent
sterilizations. It is equipped with the microprocessor for intelligent control and
man-machine interface for convenient operation. With the distinctions in
displaying parameter and condition actively, evaluating malfunction automatically,
shutting off for self-protection automatically in case of excessive temperature and
pressure, this type autoclave is reliable product in sterilizing.
1. Power source socket
2. Fuse
3. Water exit of water tank
4. Waste water exit
2 ． Application Scope
The autoclave could sterilize （ 121 ℃ or 134 ℃ ） the tooth & operation device,
Sanitary material and other heat-resisting articles of the Dept. like Stomatology,
Ophthalmology and Lab. Not for liquid & hermetical device’s sterilization.
3 ． Tech. Parameter
Chamber size of the autoclave (Diameter X Depth) 8L…… 170mmX310mm
Chamber size of the autoclave (Diameter X Depth) 16L……230mmX360mm
Chamber size of the autoclave (Diameter X Depth) 18L……249mmX355mm
Chamber size of the autoclave (Diameter X Depth) 22L……249mmX450mm
Rated Voltage………………………………………220V ± 22V, 50Hz ± 1Hz
………………………………………110V ± 11V, 60Hz ± 1Hz
Rated Power……………………………………… 1800VA
2000VA
Sterilizing (Pressure/temp.)…………………………………100-120KPa/121 º C
200-220KPa/134 º C
(Both of above are under Standard Atmospheric Pressure)
Fuse-Melting pipe……………………….. ……. T15A
T30A
Capacity of water tank………………………………………………………2L
Probable water consumption of one cycle …………………………….. . .0.4L
Environment temperature of operate……………………………………0-40 º C 4
4 ． Diagram Specification
Attention and warning
I Sort B model device
Protective Grounding
5 ． Installation
The clearance between the exterior side surface of the autoclave and the ambient
neighboring articles shall be 10cm as retained, and the top surface shall be 20cm
retained.
The air-cooling window attached to the exterior surface of the autoclave shall be
non-clog by dust or articles, and the autoclave shall be located in the proper air
flowing environment by recommendation of the supplier.
Autoclave shall be installed on the horizontal working base. 2pcs front feet
can be adjusted the height to ensure the front of machine slightly higher than
the back.
Dental chair unit
dental unit chair
dental highspeed handpiece
dental lowspeed handpiece
dental implant handpiece
dental implant motor
dental implant surgical handpiece
dental implant air rotor
dental implant machine
dental electronic surgical cutter
dental ultrasonic scaler
dental air scaler
dental k files
dental h files
dental k reamer files
dental cleaning machine
dental ultrasonic cleaner
dental sterilization pouch
dental autoclave
dental air compressor
dental suction machine
dental instrument
dental forcept
dental lab equipment
dental milling machine
dental curing light
dental disinfection box
orthodontic bracket
orthodontic wire
orthodontic niti wire
orhtodontic adhesive material
dental chair lamp
dentla sterilization pouch
dental endo motor
dental apex locator
dental needle
dental irrigation needle
dental articulator
dentures
dental accessories
dental equipment
dental spare part
dental lamp
dental x ray sensor
dental nitifile
dental taper file
dental manufactory
dental endo motor
dental apex locator
dental endo treatment
dental implant
dental product
dental equipment
dental factory
dental impression material
dental alginate material
dental alginate powder
dental impression powder
dental composite
dental adhesive
dental patient chair
clinic patient chair